Drywall Zone

    Drywall Tools   Catalog   My account   View cart    
Drywall Tools   |   Most Popular Parts   |   Contact Us   |   Shop by Logo   |   Coverage Calculator   |   New Product Annoucements   |   Columbia Schematics   |   Tapetech Schematics   |   Gift certificates   |   Site map
 Cart is empty
 ( View cart   Checkout )

  Blueline Original 6' Taper

Blueline Original 6' Taper
Currently Out Of Stock!
 Product options:
MK09 Taper Kit   

Customers Also Bought

Blueline original mega 72" (6') automatic taper is the answer for high ceilings.


The automatic taper simultaneously applies tape and joint compound to any joint: walls, corners, and ceilings. It automatically dispenses the correct amount of joint compound under the tape, regardless of the tool user's speed.

The automatic taper uses tape 2 1/16 to 2 1/8 inches wide. Wider tape will not fit and narrower tape will have a tendency to jam. Install the tape by removing the tape bail (retaining wire) and placing the roll of tape on the spindle with the tape unwinding clockwise as you look at the roll. Feed the tape through the tape guide with the back side of the tape facing down. When correctly installed, the tape will curl over the drive wheel.

Fill the automatic taper with joint compound using the loading pump and the gooseneck adapter. Be sure that the gate control lever is in the closed position. Place the automatic taper on the gooseneck with the filler nozzle firmly seated against the nylon seal and move the pump handle to transfer joint compound from the pail to the automatic taper. Keep the mud pail full to avoid air being pumped into the taper. To avoid overfilling, place your fingers in the open end of the tube while filling. Stop pumping when the piston reaches your fingers (approximately 9 pumps when empty.)

After loading the automatic taper, stand it on end and move the gate valve control lever to engage the drive mechanism. Now turn the key, located on the drive gear sprocket, until the joint compound covers the leading edge of the joint tape. This is necessary after each loading.

The automatic taper should be held with one hand on the control tube and the other hand at the bottom of the mud tube.

Start taping with butt joints first and then sidewall and ceiling flat joints. For ceilings, use both drive wheels for the first 4 - 6 inches of tape to secure it to the ceiling, then tilt the automatic taper toward you at a slight angle leaving only one drive wheel on the drywall surface. Walk backwards, leading with the head of the tool.

To tape vertical joints, place the taper at the bottom of the joint, parallel to and slightly above the floor. Lead with the head of the taper, as soon as possible to make tracking easier. Remember to roll with only one wheel in contact with the wall until about three inches from the top. Stop completely, cut the tape, by pulling the control tube toward you, and roll to the end of the joint on both wheels. To start the next joint, move the drive wheels lightly against the surface of the wall, starting the compound flow while advancing a new end of the tape with the control tube.

To tape horizontal joints, advance the joint compound and about 1 1/2 inches of tape by pushing forward on the control tube while rolling the drive wheels on the wall. Place drive wheels on the wall and roll along the joint. Stop about 2 1/2 inches from the end of the joint and cut the tape. Roll out the last 2 1/2 inches of tape while feeding tape with the control tube. This will apply compound to the beginning of the tape for the next joint.

To tape inside angle joints, both wheels must run in contact with the adjacent wall surfaces, bisecting the angle with the automatic taper. Tracking must be in a straight line with the creaser wheel extended, using the trigger located near the trailing end of the automatic taper. The extended creaser wheel secures the tape to the angle and eases the rolling operation. Avoid twisting the taper as you move along the angle to insure that you bisect the angle correctly. Operating the taper at a 45 degree angle to the joint, as soon as it is practical, will aid in the prevention of the tape "creeping".


This tool must be washed with a brush and water (or a water hose) after each use. Pay close attention that all joint compound is flushed from under the cover plate and the tape advance mechanism. Complete the clean-up by lightly oiling all wear points.

Blade Replacement

Hold the key ring, pull down and turn key ring 90 degrees. Let the key ring slide into the cutter spring tube.
Pull the cutter chain until cutter block and blade are clearly in view.
Loosen the cutter block screw and remove the used blade.
Insert a new blade. Tighten the screw, making sure the blade does not protrude through the bottom of the cutter block.
Pull the cutter block back into the taper head channel.
Pull the key ring down to the end of the spring tube. Turn it 90 degrees and lock it into the original position.
Pull down on the control tube to make sure the blade travels freely through the taper head channel.

Cable Replacement

Remove all the mud from the automatic taper.
Unscrew the butt ring from the bottom of the taper tube. Lightly tap tube butt ring with a screwdriver, if necessary.
Remove the cover plate by taking out the top screws and loosening the side and bottom screws. Gently pull the cover plate up and out to remove it. Close the gate valve and force the piston down with a thin piece of wood or a flattened piece of corner bead.
Loosen the screw on the cable drum and remove the end of the cable from the drum.
Remove the cable from the piston by removing the nut from the slotted stud.
Clean the slotted stud of any mud, then thread the cable through the nut while holding it, and place the end of the cable into the slot. Screw the nut onto the slotted stud and tighten, to secure the cable to the piston.
Drop the loose end on the cable into the tube followed by the piston. Replace the butt ring and the screws.
Make sure the slot in the cable drum is clean and insert the loose end of the cable and tighten the screw.
Wind the cable onto the cable drum by turning the drum key clockwise.
Replace the cover plate and tighten all screws.

Gooser Needle Replacement

Holding onto the gooser needle assembly, loosen the screw and remove the gooser needle. Slide the entire gooser assembly to the bottom of the tape guide. Push the new gooser needle through the hole and out the bottom so that the point of the needle protrudes 1/16 inch through the tape in the slide. Hold the support assembly and tighten the screw. Insert tape through the tape guide and check for proper advancement of the tape.


Blueline USA Tools

Blueline Gooseneck

Blueline Gooseneck

Tapetech Tools

Tapetech Finish Set


Tapetech Finish Set
Currently Out Of Stock!



Ames Bazooka Oil-5oz

Ames Bazooka Oil-5oz
Currently Out Of Stock!

We will not only beat our compeditors on quality tools and parts we will match and even beat them with a higher end tool or part